收藏本站
SPECIFICATION CONTROL DRAWING
Thermofit Assembly Procedure
1.
2.
3.
4.
5.
Strip the wires and install crimp type connector or solder wires together. Connector should be installed so that
1/6 ± 1/32 of conductor is exposed between the connector and the wire insulation, as shown in Figure 1.
Choose the proper size cap from the chart below. Place splice into cap so that the connector bottoms on the
rounded end of the cap.
Heat the assembly, using a Thermogun, Model 500A, or equivalent, equipped with a TG-12 or TG-13A
reflector.
The average length of time required for proper heating is given in the chart. However, since the heat sink effect
of various wire bundles may vary considerably, several trial specimens should be crossed-sectioned as shown in
Figure 2 before proceeding with production installations. If the area between the wires is not completely filled,
a longer heating cycle should be established.
With wire bundles of more than three wires, it is helpful to slightly deform the cap by pinching in the area
above the connection at the end of the heating cycle and then returning the cap to the heat for an additional
period to allow the cap to return to its cylindrical shape.
Chart 1
Part
Name
D-300-01
D-300-02
D-300-03
Figure 1
Splicer Diameter
Minimum Maximum
2.03 (0.080) 4.91 (0.165)
3.04 (0.120) 6.35 (0.250)
4.57 (0.180) 8.89 (0.350)
Figure 2
Time
(sec.)
30
45
60
Bundle Diameter
Maximum
.115
.200
.300
307 Constitution Drive Menlo Park, CA 94025, USA
Wire and
Harnessing
Products
TITLE :
CAP, SPLICE ENCAPSULATION
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS.
INCHES DIMENSIONS ARE BETWEEN BRACKETS.
DOCUMENT NO.:
D-300-01/-03
TOLERANCES:
0.00 N/A
0.0 N/A
0 N/A
ANGLES: N/A
ROUGHNESS IN
MICRON
Tyco Electronics reserves the right to amend
this drawing at any time. Users should
evaluate the suitability of the product for
their application.
DCR NUMBER:
D010043
REPLACES:
N/A
DRAWN BY:
M. FORONDA
DATE:
15-Feb.-01
PROD. REV.
SEE TABLE
DOC ISSUE:
1
SCALE:
None
SIZE:
A
SHEET:
7 of 7
If this document is printed it becomes uncontrolled. Check for the latest revision.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
D-436-0098 SOLDER SLEEVE .025" DIA IMM RES
D-500-L455-3-613-120 MICROSOUPLER 3 STUB DBL SHIELD
D-659-0026 HEAT SHRINK SLD SLEEVE SHIELD
D06D80 RELAY SSR 80A 0-60V DC OUTPUT
D15532-000 HX-SCE-1K-12.7-50-4
D1A05HD RELAY REED SPST 500MA 5V
D1D60 RELAY SSR 60A DC PANEL MOUNT
D2W203F RELAY SSR 3A SIP DC
相关代理商/技术参数
D-300-02CS1108 制造商:TE Connectivity 功能描述:D-300-02CS1108
D-300-02CS834 功能描述:焊料和屏蔽管 RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03
D-300-03 功能描述:焊料和屏蔽管 Splice Encap. Cap 12AWG 3 Wires RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03
D-300-03CS1108 制造商:TE Connectivity 功能描述:D-300-03CS1108 制造商:TE Connectivity 功能描述:Cap, Splice Encapsulation
D-300-03CS834 功能描述:焊料和屏蔽管 RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03
D-300-08 功能描述:焊料和屏蔽管 RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03
D300-08 制造商:TE Connectivity 功能描述:
D-300-08CS1108 功能描述:焊料和屏蔽管 Splice Encap. Cap 2.03-3.04 Dia RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03